Student Exploration: Electromagnetic Induction

Name: Samantha Wisniewski Date: 4/29 Student Exploration: Electromagnetic Induction Directions: Follow the instructions to go through the simulation. Respond to the questions and prompts in the orange boxes. Vocabulary: current, electric field, electromagnetic induction, magnetic field, magnetic flux, right-hand rule, vector, voltage, wind generator Prior Knowledge Question (Do this BEFORE using the Gizmo.) A wind generator, such as the one shown at left, uses the power of wind to generate electricity. What do you think is happening inside the wind generator to convert the energy of the spinning blades into electricity? Make your best guess. As the big blades are pushed it spins a generator which makes electricity. Gizmo Warm-up Usually when you experiment with circuits, you use a battery or another energy source to create a current. But is it possible to generate a current without a battery? You can find out with the Electromagnetic Induction Gizmo. In the Gizmo, you can drag the wire loop around or use the controls to move the magnet up and down. You can also rotate the wire loop. Experiment with the Gizmo to see how many different ways you can create a current in the wire loop and light the light bulb. Describe your findings below. It is brightest when the magnet is super close or super far. Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved​ Activity A: Electromagnetic fields Get the Gizmo ready: ●​ Turn on Show electric field at sensor. ●​ Click Reverse to move the magnet down and set the Speed to 10 cm/s. Introduction: When electric current runs through a wire, it induces a magnetic field near the wire. Similarly, electric fields can be created in the process of electromagnetic induction. Question: How do magnets induce electric fields? 1. Observe: While the magnet is not moving, is there any electric field? Yes 2. Sketch: Click Forward, and observe the electric field display. (Note: This display shows a top view of the electric field picked up by the sensor at the top of the SIMULATION pane.) Sketch the electric field at right. (Click on the picture, select EDIT to use the drawing tool.) ✏️ ✏️ Notice the electric field consists of an array of arrows, or vectors. Each vector represents the force on a positive charge located at the base of the vector. What do you notice? The arrows are evenly distanced. 3. Experiment: Click Reverse and observe the electric field as the magnet moves away. A.​ How does changing the direction of the magnet affect the electric field? The electric field is farther away. B.​ Increase the Speed to 20 cm/s, and then click Forward. How does increasing the speed of the magnet affect the strength of the electric field? The positive charge is stronger. 4. Make a rule: If you have studied how currents induce magnetic fields, you may recall the right-hand rule, illustrated at right. For electric currents, the thumb represents the direction of positive charge (I) and the fingers represent the induced magnetic field (B). To describe the electric field induced by a moving magnet, you can use a “left-hand rule.” What do the thumb and fingers of your left hand represent in this case? Thumb: the direction of the - charge Fingers: the magnetic feild Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved​ Activity B: Induced currents Get the Gizmo ready: ●​ Check that Show electric field at sensor is on. ●​ Click Reverse to move the magnet down and set the Speed to 10 cm/s. Question: How do magnets induce electric currents? 1.​ 📷 Observe: Drag the wire loop directly above the magnet. Click Forward and observe the wire loop and light bulb. As the magnet is moving, click the camera ( ) icon to take a snapshot. Right-click the image, and click Copy Image. Paste this image into the document below. 📷 A. What do you notice in the wire? The current gets weaker B. How does the direction of the current in the loop compare to the electric field? Both the electric field and current go down. Recall that the vectors in the electric field represent the forces on positive charges. Currents in wires are carried by moving electrons, which are negatively charged. Therefore, the electrons move in the opposite direction as the arrow on the wire. C. Click Reverse. How does this affect the direction of the current? It drops. 2.​ Compare: Turn on Show loop data. The current (I) in the loop is measured in amperes. Click Forward and observe both the current and the electric field. A.​ How does the current change as the magnet approaches the loop? It goes up. B.​ How does the electric field change as the magnet approaches the loop? It goes up. Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved​ 3.​ Compare: Increase the Speed to 20 cm/s, and click Reverse to move the magnet down. Click Forward and observe both the current and the electric field. A.​ How does increasing the magnet’s speed affect the current? It makes the current drop faster. B.​ How does increasing the magnet’s speed affect the electric field? It drops faster making it weaker. 4.​ ✏️ Sketch: 5.​ Gather data: Click Reverse to move the magnet down to the bottom. The wire loop should be directly above the magnet, as low as you can drag it. A. How many magnetic field lines are currently going through the loop? 0 B. Click Forward and wait until the magnet gets to the top. How many field lines are passing through the loop now? 3 6.​ Observe: The number of lines is proportional to the magnetic flux (ΦM) through the loop. Magnetic flux is a measure of how powerful the magnetic force is through a given area. An electric current can only be induced if the magnetic flux is changing through the loop. Click Reverse to move the magnet to the bottom. Turn on Show loop data and click Forward. How does the magnetic flux change as the magnet rises? It goes higher. 7.​ Draw conclusions: In general, how do the current and electric field relate to the change in magnetic flux? The current is made by a change in the magnetic field. The flow of current is made because of the EMF made by the changing magnetic field, it doesn’t matter if there is a current path. 8.​ Challenge: Michael Faraday (1791–1867), who is generally credited as the discoverer of electromagnetic induction (in 1831), discovered the relationship between voltage (V), the force that creates a current in a Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved​ wire, and the magnetic flux. Faraday’s law of magnetic induction relates voltage to the change in magnetic flux (ΔΦM) and the time interval (Δt). Based on the observations you have made, what is Faraday’s law? Check your answer with your teacher. V= Activity C: Moving the loop the negative rate of change of magnetic flux through the circuit Get the Gizmo ready: ●​ Click Forward to move the magnet to the top. ●​ Turn off Show magnetic field. Question: Can electric currents be induced by moving the wire loop? 1.​ Predict: Do you think you can induce an electric current in the wire loop by moving or rotating the loop? Explain why or why not. Yes because the magnetic field could be stronger in some places. 2.​ Observe: Check that Show loop data is on. Move the wire loop up, away from the magnet. A. Is a current produced in the wire? No B. If so, in which direction is the current moving, left or right? right C. Is this motion of the loop equivalent to the magnet moving up or down? D. Is the magnetic flux increasing or decreasing as you do this? nowhere decreasing 3.​ Observe: Move the wire loop down, towards the magnet. A. In which direction is the current moving? up B. Is this motion of the loop equivalent to the magnet moving up or down? C. Is the magnetic flux increasing or decreasing as you do this? up increasing 4.​ Summarize: In general, what is the direction of the current if the magnetic flux is increasing? What is the direction when the magnetic flux is decreasing? Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved​ Clockwise from the top. The increasing current through the circuit is because the magnetic field is upward, so the induced magnetic field is downward. 5.​ Explore: Try moving the loop slowly, then fast. Observe the magnitude of the current as you do this. How does the speed of the loop affect the current? The current goes up then down. 6.​ Experiment: Drag the loop to the left edge, and then slowly move the loop horizontally to the right edge. Observe the flux as you do this. A. Is a current produced in the wire? a small amount B. What do you notice about the direction of the current as the wire crosses the midpoint? It shift back and forth C. What causes the direction of the current to change? the position of the wire does. 7.​ Experiment: Turn on Show magnetic field. Position the loop over the magnet. Click Play ( you notice? ). What do The current and flux stay at 100% the whole time but change from positive to negative. 8.​ Explain: As the loop rotates, why is a current induced in the loop? because of the magnetic field. 9.​ Apply your knowledge: At the beginning of this exercise, you were asked to guess how a wind generator uses the power of wind to produce an electric current. Now you can use what you have learned to explain what is really happening. Add a sketch below if you like. ✏️ How does a wind generator work? It spins a generator which has magnets that change the magnetic field to generate an electric charge that it stores. Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved​ Reproduction for educational use only. Public sharing or posting prohibited. © 2020 ExploreLearning™ All rights reserved