Door Hardware Ch2

<%Insert Project Name%> 2.17 A. MECHANICAL STOPS AND HOLDERS Floor-Mounted Stops: BHMA A156.16 . 1. Basis-of-Design Product: Subject to compliance with requirements, provide Ives Hardware type FS18, or comparable product by one of the following: a. b. c. d. 2.18 A. ELECTROMAGNETIC STOPS AND HOLDERS Electromagnetic Door Holders: BHMA A156.15, Grade 1; wall-mounted electromagnetic single unit with strike plate attached to swinging door; coordinated with fire detectors and interface with fire alarm system for labeled fire-rated door assemblies. 1. Basis-of-Design Product: Subject to compliance with requirements, provide Sargent Manufacturing Company 1560 Series, or comparable product by one of the following: a. b. 2.19 A. A. Rixson Specialty Door Controls, model 994/996, Substitutions: See Section 01 25 00 - Substitution Procedures. OVERHEAD STOPS AND HOLDERS Overhead Stops and Holders: BHMA A156.8. 1. Basis-of-Design Product: Subject to compliance with requirements, provide GlynnJohnson 100 Series, or comparable product by one of the following: a. b. c. 2.20 Hager Companies.Rockwood Manufacturing Company. McKinney Products Company; an ASSA ABLOY Group company . Rockwood Manufacturing Company Substitutions: See Section 01 25 00 - Substitution Procedures. Rockwood Manufacturing Company, 11000 Series. SARGENT Manufacturing Company; an ASSA ABLOY Group company , 690 Series. Substitutions: See Section 01 25 00 - Substitution Procedures. DOOR GASKETING Door Gasketing: BHMA A156.22; air leakage not to exceed 0.50 cfm per foot of crack length for gasketing other than for smoke control, as tested according to ASTM E 283; with resilient or flexible seal strips that are easily replaceable and readily available from stocks maintained by manufacturer. 1. Basis-of-Design Product: Subject to compliance with requirements, provide National Guard Products 127NA seals and 199NA sweeps, or comparable product by one of the following: a. b. c. Pemko Manufacturing Co.; an ASSA ABLOY Group company , 375_R seals and 368_N sweeps. Reese Enterprises, Inc., DS70C seals and 323A sweeps. Substitutions: See Section 01 25 00 - Substitution Procedures. AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 11 <%Insert Project Name%> 2.21 A. THRESHOLDS Thresholds: BHMA A156.21; fabricated to full width of opening and full depth of frame. 1. Basis-of-Design Product: Subject to compliance with requirements, provide National Guard Products Flat Saddle, 1/4" height, thresholds, or comparable product by one of the following: a. b. c. 2.22 A. METAL PROTECTIVE TRIM UNITS Metal Protective Trim Plate Units: BHMA A156.6; fabricated from minimum 0.060-inch- thick stainless steel; with manufacturer's standard machine or self-tapping screw fasteners. 1. Basis-of-Design Product: Subject to compliance with requirements, provide Trimco KX064 series plates, or comparable product by one of the following: a. b. c. B. Basis-of-Design Product: Subject to compliance with requirements, provide Trimco KE33-1 edge guards, or comparable product by one of the following: a. b. c. A. Electrical Power Transfer: Basis-of-Design Product: Subject to compliance with requirements, provide Von Duprin EPT-10, or comparable product by one of the following: a. A. Burns Manufacturing Incorporated, Model 303. Rockwood Manufacturing Company, model 306. Substitutions: See Section 01 25 00 - Substitution Procedures. AUXILIARY ELECTRIFIED DOOR HARDWARE 1. 2.24 Burns Manufacturing Incorporated, K1062 series. Rockwood Manufacturing Company, XP62 series. Substitutions: See Section 01 25 00 - Substitution Procedures. Metal Protective Trim Door Edge Units: BHMA A156.6; fabricated from minimum 0.050-inchthick stainless steel; with manufacturer's standard machine or self-tapping screw fasteners. 1. 2.23 Pemko Manufacturing Co.; an ASSA ABLOY Group company . Reese Enterprises, Inc. . Securitron Magnalock Corp.,www.securitron.com, model EPT/EPTL. FABRICATION Base Metals: Produce door hardware units of base metal indicated, fabricated by forming method indicated, using manufacturer's standard metal alloy, composition, temper, and hardness. Furnish metals of a quality equal to or greater than that of specified door hardware units and BHMA A156.18. AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 12 <%Insert Project Name%> B. Fasteners: Provide door hardware manufactured to comply with published templates prepared for machine, wood, and sheet metal screws. Provide screws that comply with commercially recognized industry standards for application intended, except aluminum fasteners are not permitted. Provide Phillips flat-head screws with finished heads to match surface of door hardware, unless otherwise indicated. 1. Concealed Fasteners: For door hardware units that are exposed when door is closed, except for units already specified with concealed fasteners. Do not use through bolts for installation where bolt head or nut on opposite face is exposed unless it is the only means of securely attaching the door hardware. Where through bolts are used on hollow door and frame construction, provide sleeves for each through bolt. 2. Fire-Rated Applications: a. Wood or Machine Screws: For the following: 1) 2) 3) b. Steel Through Bolts: For the following unless door blocking is provided: 1) 2) 3. 4. 5. 2.25 Hinges mortised to doors or frames; use threaded-to-the-head wood screws for wood doors. Strike plates to frames. Closers to doors and frames. Closers to doors and frames. Surface-mounted exit devices. Spacers or Sex Bolts: For through bolting of hollow-metal doors. Fasteners for Wood Doors: Comply with requirements in DHI WDHS.2, "Recommended Fasteners for Wood Doors." Gasketing Fasteners: Provide noncorrosive fasteners for exterior applications and elsewhere as indicated. FINISHES A. Provide finishes complying with BHMA A156.18 as indicated in door hardware schedule. B. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. C. Appearance of Finished Work: Variations in appearance of abutting or adjacent pieces are acceptable if they are within one-half of the range of approved Samples. Noticeable variations in the same piece are not acceptable. Variations in appearance of other components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast. AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 13 <%Insert Project Name%> PART 3 - EXECUTION 3.1 EXAMINATION A. Examine doors and frames, with Installer present, for compliance with requirements for installation tolerances, labeled fire-rated door assembly construction, wall and floor construction, and other conditions affecting performance. B. Examine roughing-in for electrical power systems to verify actual locations of wiring connections before electrified door hardware installation. C. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 A. INSTALLATION Mounting Heights: Mount door hardware units at heights to comply with the following unless otherwise indicated or required to comply with governing regulations. 1. Standard Steel Doors and Frames: ANSI/SDI A250.8. 2. 3. B. Custom Steel Doors and Frames: HMMA 831. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for Wood Flush Doors." Install each door hardware item to comply with manufacturer's written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing. Do not install surface-mounted items until finishes have been completed on substrates involved. 1. 2. Set units level, plumb, and true to line and location. Adjust and reinforce attachment substrates as necessary for proper installation and operation. Drill and countersink units that are not factory prepared for anchorage fasteners. Space fasteners and anchors according to industry standards. C. Hinges: Install types and in quantities indicated in door hardware schedule but not fewer than the number recommended by manufacturer for application indicated or one hinge for every 30 inches of door height, whichever is more stringent, unless other equivalent means of support for door, such as spring hinges or pivots, are provided. D. Intermediate Offset Pivots: Where offset pivots are indicated, provide intermediate offset pivots in quantities indicated in door hardware schedule but not fewer than one intermediate offset pivot per door and one additional intermediate offset pivot for every 30 inches of door height greater than 90 inches. E. Lock Cylinders: Install construction cores to secure building and areas during construction period. 1. Furnish permanent cores to Owner for installation. AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 14 <%Insert Project Name%> F. Boxed Power Supplies: Locate power supplies as indicated or, if not indicated, above accessible ceilings . Verify location with Architect. 1. Configuration: Provide least number of power supplies required to adequately serve doors with electrified door hardware. G. Thresholds: Set thresholds for exterior doors and other doors indicated in full bed of sealant complying with requirements specified in Section 07 92 00 "Joint Sealants." H. Stops: Provide floor stops for doors unless overhead stops are indicated in door hardware schedule. Do not mount floor stops where they will impede traffic. I. Perimeter Gasketing: Apply to head and jamb, forming seal between door and frame. J. Meeting Stile Gasketing: Fasten to meeting stiles, forming seal when doors are closed. K. Door Bottoms: Apply to bottom of door, forming seal with threshold when door is closed. 3.3 A. FIELD QUALITY CONTROL Independent Architectural Hardware Consultant: Owner will engage a qualified independent Architectural Hardware Consultant to perform inspections and to prepare inspection reports. 1. 3.4 A. ADJUSTING Initial Adjustment: Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements. 1. B. 3.5 Independent Architectural Hardware Consultant will inspect door hardware and state in each report whether installed work complies with or deviates from requirements, including whether door hardware is properly installed and adjusted. Door Closers: Adjust sweep period to comply with accessibility requirements and requirements of authorities having jurisdiction. Occupancy Adjustment: Approximately six months after date of Substantial Completion, Installer's Architectural Hardware Consultant shall examine and readjust each item of door hardware, including adjusting operating forces, as necessary to ensure function of doors, door hardware, and electrified door hardware. CLEANING AND PROTECTION A. Clean adjacent surfaces soiled by door hardware installation. B. Clean operating items as necessary to restore proper function and finish. AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 15 <%Insert Project Name%> C. 3.6 A. Provide final protection and maintain conditions that ensure that door hardware is without damage or deterioration at time of Substantial Completion. DEMONSTRATION Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain door hardware and door hardware finishes. Refer to Section 01 79 00 "Demonstration and Training." PART 4 - HARDWARE SETS 4.1 GENERAL A. These Hardware Sets indicate requirements for single doors of that type, with conditional requirements for pairs and other situations. B. Pairs of Swinging Doors: Provide one of each specified item on each leaf unless specifically stated otherwise. Treat pairs as two active leaves unless otherwise indicated. C. HW-CYL: Doors Whose Hardware is Specified in Other Sections But Which Must Be Keyed to Building System: 1. D. 4.2 A. HW-0: Doors/Openings Whose Hardware is Specified in Other Sections, and No Locking is Required. SWING DOORS - NOT REQUIRING KEY LOCKING HW-1: Push/Pull, Non-Fire Rated: 1. 2. B. Closer. Push/Pull. Armor Plate. Edge Guards. HW-2: Latchset, Non-Fire-Rated 1. D. Closer. Push/Pull. HW-1P: Push/Pull, Non-Fire-Rated, Protection: 1. 2. 3. 4. C. Lock Cylinder, Mortise. Latchset, Passage. HW-2P: Latchset, Non-Fire-Rated, Protection: AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 16 <%Insert Project Name%> 1. 2. 3. E. HW-2AP: Latchset, Automatic, Fire-Rated (and not fire-rated if closer required), Protection: 1. 2. 3. 4. 5. 6. F. A. A. HW-10: Office, Non-Fire-Rated: HW-20: Secure Classroom Lock, Non-Fire-Rated: Lockset, ANSI F13. HW-20P: Secure Classroom Lock, Non-Fire-Rated, Protection: 1. 2. C. Lockset, Office SWING DOORS - KEY REQUIRED TO LOCK, MAY BE LEFT UNLOCKED 1. B. Closer. Lockset, Privacy. SWING DOORS - LOCKABLE, MAY BE LEFT UNLOCKED, KEY NOT REQUIRED TO LOCK 1. 4.4 Lockset, Privacy. HW-5F: Privacy Lockset, Fire-Rated: 1. 2. 4.3 Closer. Latchset, Passage. Armor Plate. Adge Guards. HW-5: Privacy Lockset, Non-Fire-rated: 1. H. Closer. Latchset, Passage. Power Operator, Power-Assist. Actuators, Wall-Mounted, both sides, location as indicated on drawings. Armor Plate. Edge Guards. HW-2FP: Latchset, Fire-Rated (and not fire-rated where closer required), Protection: 1. 2. 3. 4. G. Latchset, Passage. Armor Plate. Edge Guards. Lockset, ANSI F13. Kick Plate. HW-20F: Secure Classroom Lock, Fire-Rated on Non-Fire-Rated Where Self-Closing is Required: AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 17 <%Insert Project Name%> 1. 2. 3. 4.5 A. Closer. Lockset, ANSI F13. Pair: One leaf inactive; automatic or self-closing flush bolts as required to comply with code. If door fire rating requires astragal, provide coordinator. SWING DOORS - ELECTRICAL ACCESS CONTROL HW-52: Entry Control, Electrified Lock, Fail-Secure, Fire-Rated and non-Fire-Rated: 1. 2. 3. Card Reader, located where indicated on drawings. Closer. Lockset, Always-Locked, Electric Bolt Retraction: a. b. c. 4. 5. Fail-Secure, remaining locked in event of fire alarm activation or power failure. Key override and free egress at all times. Entry Control: Upon signal from access control device, outside trim unlocks. Power Supply. Electrical Power Transfer END OF SECTION 08 71 00 AE Project #: <%%> Revision Date: 01/29/2018 Door Hardware 08 71 00 - 18