University:
Massachusetts Institute of Technology
Course:
6.061 | Introduction to Electric Power Systems
Academic year:

2019
Views:

238

Pages:

3
Author:

Giruzzir6l

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.061/6.690 Introduction to Power Systems Solution To Problem Set 1 Problem 1: Simple Problems from the book 1. 240v × 50A = 12kW 12kW × 3, 414BTU/kWh = 40, 968BTU/h 2. R = 3,414 .5 = 6, 828BTU/kWh 3. Assume Coal energy content is 30,870 BTU/kg. If R=11,000 BTU/kWh, then coal consumption is: ṁ = 11, 000BTU/kWh ≈ 0.3563kg/kWh 30, 870BTU/kg Then, if P = 1000M W = 106 kW , Ṁ = 106 kW × .3563 = 3.563 × 105 kg/h ×365.25 × 24 = 3.12 × 109 kg/yr = 3.12 × 106 Tonnes/yr 4. If R = 30, 890BTU/kWh, ṁ = ×2.959kg CO2 /kg fuel = 9, 500BTU/lWh ≈ .3075kg/kWh 30, 890BTU/kg 0.9kg CO2 /kWh ×600, 000 × 24 × 365.25 = 4.79 × 109 kg CO2 /yr = 4.79 × 106 T CO2 /yr Problem 2: This problem is solved by superposition: Consider one source at a time and add the solutions. Voc = 1 × 8||8 + 10 × Isc = 1 × 8 =4+5 =9 8+8 8||4 1 5 9 4 + 10 × × = .5 + = 4 + 8||8 8 + 8||4 4 8 8 1 Voc Note that Rth = 4 + 8||8 = 8 and this conﬁrms the previous answer: Isc = R th Then: 1 8 = 9 × = 4.5 V = Voc × 8+8 2 Problem 3: There is a handy-dandy formula in Chapter 4 for this problem, expression 4.12. R1 = R2 = 5 × 10 =2 5 + 101 0 10 × 10 =4 5 + 10 + 10 But this one can be done easily using more ad-hoc methods. Note driving point impedance is: R1 + R2 = 10||15 = 6 Then the voltage divider ratio is: 10 2 R2 = = R1 + R2 15 3 From which it is straightforward to conclude that R2 = 6 × 2/3 = 4 and R1 = 6 − R2 = 2. Problem 4: The bridge can be characterized as a thevenin equivalent circuit. Without the hori zontal resistor of value one, the open circuit voltage will be: Voc = 18 × � 4 1 − 5 5 � = 18 × 3 5 The Thevenin equivalent resistance is Rth = 2 × 1||4 = 58 . So then, with the resistor of value one is in place: Vo = 18 × 1 3 × 5 1+ 8 5 = 54 13 Problem 5: This is approximately the picture you should get. 6.061 Homework Set 1 1 0.8 Function Value 0.6 0.4 0.2 0 −0.2 −0.4 −0.6 −0.8 0 0.05 0.1 0.15 0.2 0.25 Time, s 0.3 0.35 0.4 0.45 0.5 Figure 1: Answer for Problem 5 2 Problem 6: For 6.690 only The key to doing this easily is shown in Figure 2, where one of the cells of the ladder is called out. It is easy to see that the driving point impedance of that cell of the ladder is simply 2R||2R = R and the transfer relationship between input and output is V = 12 V−1 . Moving left one cell, it is also clear the the driving point resistance looking into the cell is still just R and the transfer is V−1 = 12 V−2 . This is true of each successive cell until we reach the source. The voltage divider ratio between the source and the node just above 2R||2R = V3s . the source is Vn = Vs × 2R+2R||2R In this case, V = V1 × 31 ×2−6 +V2 × 31 ×2−5 if V1 = V2 = 5, this becomes: V = 35 × 5 3 × 3 2 × 1 32 = 5 64 ≈ .078125 R R R R R R R + + V 0 2R 2R 2R 2R 2R V 2R R − − R + + R d V−1 − R 2R − R R d + V −2 − + 2R Figure 2: Magic Ladder Circuit 3 V R V −1 − � 1 32 + 1 64 � =