Photosynthesis Virtual Lab: Exploring Light and Growth

Name: _______________________________________________________ Date: __________________________ Manipulating Photosynthesis - Virtual Lab Pre-Lab Questions ● To survive, what gas do we need to breathe in? ___________________________________ ● Where is this gas produced? __________________________________________________ Introduction During photosynthesis, plants use the energy of light to produce glucose (C6H12O6) from carbon dioxide (CO2), and water (H2O). Glucose is a simple sugar that plants use for energy and as a building block for larger molecules. A by-product of photosynthesis is oxygen. Plants use some of the oxygen they produce, but most of it is released. In the Photosynthesis Lab Gizmo™, you can monitor the rate of photosynthesis by measuring oxygen production. 1. Observe the left pane closely. What do you think the bubbles are? _______________________ 2. Select the BAR CHART tab. On the graph, notice the Oxygen production bar. Move the Light intensity slider back and forth. How does light intensity affect oxygen production? _________________________________________________________________________ 3. Experiment with the vertical Temperature slider (upper left) and the CO2 level slider. A. How does temperature affect oxygen production? B. How does CO2 level affect oxygen production? C. How does oxygen production relate to the rate of photosynthesis? Part A: Ideal conditions Get the Gizmo ready: ● Be sure that the BAR CHART tab is selected. ● Turn on Show numerical values. Question: What are the ideal conditions for photosynthesis? 1. Hypothesis: During photosynthesis, light energy is used to synthesize carbon dioxide (CO2) and water (H2O) into glucose (C6H12O6) and oxygen (O2). The complex series of chemical reactions is summarized by the following formula: 6CO2 + 6H2O + light energy → C6H12O6 + 6O2 What light intensity and CO2 level do you think will maximize the rate of photosynthesis? ___________________________________________________________ 2. Experiment: Use the Gizmo to find the ideal conditions for photosynthesis. Use any method you like. When you think you have the answer, list the conditions below. Temperature Light intensity CO2 level Oxygen production 3. Revise and repeat: One way to test if you’ve found the ideal conditions is to change each variable slightly from the value that you recorded above. If the oxygen production decreases with each change that you make, it is likely you have found the ideal conditions. If a small change causes oxygen production to increase, continue to experiment. If necessary, revise your numbers in the table above. 4. Think about the process of finding the ideal conditions. A. Why would it be hard to find the ideal light intensity if the temperature were very hot or cold? B. Why would it be hard to find the ideal CO2 level if the light intensity were very low? Get the Gizmo ready: Part B: Colored light ● Select the COLOR tab and the BAR CHART tab. ● Set the Temperature to 24°C, the Light intensity to 90%, and the CO2 level to 1,000 ppm. Introduction: Plants use a green pigment called chlorophyll to absorb light and convert its energy into a form that the plant can use. Chlorophyll gives plants their green color. Question: What color of light is the best for photosynthesis? 1. Observe: The color of a light wave is determined by its wavelength. On the COLOR tab, slowly drag the Light wavelength slider back and forth and observe the effect on oxygen production. How does the color of light affect the rate of photosynthesis? 2. Hypothesis: Which color of light do you think will maximize the rate of photosynthesis? 3. Gather data: Set the Light wavelength to 400 nm. (The symbol “nm” stands for nanometers. A nanometer is a billionth of a meter.) Visible light ranges from 400 to 700 nm. On the TABLE tab, click Record data. Then set the Light wavelength to 420 nm, and repeat. Continue recording data in the Gizmo every 20 nm until the wavelength is 700 nm. 4. Graph: Select the GRAPH tab and select Wavelength. Sketch the graph in the space at right. A. Which colors were absorbed best by the plant? _______________________________________ B. Which colors were absorbed worst? _______________________________________ 5. When we look at a leaf, we see the colors of light that are reflected off its surface. How does this explain the relatively low flow of oxygen in green light? Get the Gizmo ready: Part C: Limiting factors ● Select the WHITE tab and the BAR CHART tab. ● Turn on Show numerical values. Introduction Photosynthesis requires light, water, and CO2 to work. When one of these factors is in short supply, it is called a limiting factor. Temperature can also be a limiting factor when it is too hot or too cold for photosynthesis to work well. Question: What is the effect of limiting factors on photosynthesis? 1. Set Temperature to 24°C, Light intensity to 50%, and CO2 level to 200 ppm. A. Move the Temperature slider up and down. Were you able to increase oxygen production? _____________________ (Return the slider to 24°C when finished.) B. Move the Light intensity slider back and forth. Were you able to increase oxygen production? _____________________ (Return the slider to 50% when finished.) C. Move the CO2 level slider back and forth. Were you able to increase oxygen production? _____________________ (Return the slider to 200 ppm when finished.) 2. In this situation, what was the limiting factor? _____________________________ How do you know? 3. In each of the situations below, use the Gizmo to find the limiting factor. Temperature Light intensity CO2 level 25°C 60% 700 ppm 15°C 20% 200 ppm 30°C 50% 400 ppm Limiting factor 4. Suppose you were a farmer trying to grow plants in a greenhouse. Why would it be important to know what the limiting factor is? Photosynthesis Virtual Lab Vocabulary New and Old Terms ● Carbon dioxide – a colorless, odorless gas that is produced during respiration and combustion (burning). o Carbon dioxide is used by plants during photosynthesis. o The chemical formula of carbon dioxide is CO2. o Average CO2 concentrations in Earth’s atmosphere are about 390 ppm (parts per million). ● Chlorophyll – a green pigment in plants that absorbs light energy and converts it into a form the plant can use for photosynthesis. ● Glucose – a simple sugar that is a major energy source for cells. o Glucose is produced in photosynthesis. o The chemical formula of glucose is C6H12O6. ● Limiting factor – the required substance that is in shortest supply and therefore limits growth or other life processes. o In many ecosystems, food is the limiting factor that keeps populations in check. o For plants, nutrients such as phosphorous and nitrogen are often limiting factors in the spring and summer. Cold temperatures limit growth in the winter. ● Nanometer – a tiny unit of distance, equal to one billionth of a meter. o The symbol for a nanometer is “nm.” ● Photosynthesis – a process in which plants use energy from light to produce glucose and oxygen from carbon dioxide and water. o The chemical equation for photosynthesis is: CO2 + H2O → C6H12O6 + O2 This reads: Carbon dioxide and water react to yield glucose and oxygen. o Glucose is used by the plant for energy. It can also be used as a building block for complex sugars such as cellulose. o Some oxygen is used by the plant, but most is released. ● Wavelength – the distance between two consecutive crests of a wave. o The wavelength of visible light ranges from 400 nanometers (violet) to 700 nanometers (red).