Packet Tracer - VLSM Design and Implementation Practice

Packet Tracer - VLSM Design and Implementation Practice Topology You will receive one of three possible topologies. Addressing Table Device Interface Building 1[[R1Name]] G0/0 blank G0/1 S0/0/0 Building 2 blank blank ASw1blank ASw2blank ASw3blank ASw4blank Host-Ablank Host-Bblank blank Host-Cblank blank Host-Dblank blank G0/0 G0/1 S0/0/0 VLAN 1 VLAN 1 VLAN 1 VLAN 1 NIC NIC NIC NIC IP Address Subnet Mask Default Gateway 192.168.72.129blank 255.255.255.240blan k N/A 192.168.72.97blank 255.255.255.224blan k N/A 192.168.72.145blank 255.255.255.252blan k N/A 192.168.72.65blank 255.255.255.224blan k N/A 192.168.72.1blank 255.255.255.192blan k N/A 192.168.72.146lank 255.255.255.252blan k N/A 192.168.72.130lank 255.255.255.240blan k 192.168.72.129 192.168.72.98ank 255.255.255.224blan k 192.168.72.97bk 192.168.72.66ank 255.255.255.224blan k 192.168.72.65bla nk 192.168.72.2blank 255.255.255.192blan k 192.168.72.1blan k 192.168.72.142blank 255.255.255.240blan k 192.168.72.129bl ank 192.168.72.126blank 255.255.255.224blan k 192.168.72.97bla nk 192.168.72.94blank 255.255.255.224blan k 192.168.72.65bla nk 192.168.72.62blank 255.255.255.192blan k 192.168.72.1blan k Objectives Part 1: Examine the Network Requirements Part 2: Design the VLSM Addressing Scheme Part 3: Assign IP Addresses to Devices and Verify Connectivity Background In this activity, you are given a /24 network address to use to design a VLSM addressing scheme. Based on a set of requirements, you will assign subnets and addressing, configure devices and verify connectivity. Instructions Part 1: Examine the Network Requirements Step 1: Determine the number of subnets needed. You will subnet the network address . The network has the following requirements:  LAN will require 7 host IP addresses  LAN will require 15 host IP addresses  LAN will require 29 host IP addresses  LAN will require 58 host IP addresses Question: How many subnets are needed in the network topology? 5Type your answers here. Step 2: Determine the subnet mask information for each subnet. Questions: a. Which subnet mask will accommodate the number of IP addresses required for sw1 ? How many usable host addresses will this subnet support? 255.255.255.240 should accommodate 14 hosts.Type your answers here. b. Which subnet mask will accommodate the number of IP addresses required for ? How many usable host addresses will this subnet support? 255.255.255.224, should accommodate/ support 30 hostsType your answers here. c. Which subnet mask will accommodate the number of IP addresses required for ? How many usable host addresses will this subnet support? 255.255.255.224, should accommodate/ support 30 hostsType Type your answers here. d. Which subnet mask will accommodate the number of IP addresses required for ? How many usable host addresses will this subnet support? Type 255.255.255.192, should accommodate / support 62 hosts answers here. e. Which subnet mask will accommodate the number of IP addresses required for the connection between and ? 255.255.255.252 will support 2 hostsType your answers here. Part 2: Design the VLSM Addressing Scheme Step 1: Divide the network based on the number of hosts per subnet. a. Use the first subnet to accommodate the largest LAN. b. Use the second subnet to accommodate the second largest LAN. c. Use the third subnet to accommodate the third largest LAN. d. Use the fourth subnet to accommodate the fourth largest LAN. and e. Use the fifth subnet to accommodate the connection between . Step 2: Document the VLSM subnets. Complete the Subnet Table, listing the subnet descriptions (e.g. [[S1Name]] LAN), number of hosts needed, then network address for the subnet, the first usable host address, and the broadcast address. Repeat until all addresses are listed. Subnet Table Number of Hosts Needed Subnet Description User-4 LANnk User-3 LANnk blank 58blank 29blank 15blank User-2 LANnk blank Network Address/CIDR 192.168.72.0/26 First Usable Host Address 192.168.72.1lank 192.168.72.64/27 blank 192.168.72.96/27 Broadcast Address 192.168.72.63blank 192.168.72.65lank blank 192.168.72.95blank blank 192.168.72.97lank blank 192.168.72.127blan k blank 7blank 192.168.72.128/2 8 blank 192.168.72.129lank blank 192.168.72.143blan k blank 2blank 192.168.72.144/3 0 blank 192.168.72.145lank blank 192.168.72.147blan k blank User-1 LANnk blank WAN Link nk blank Step 3: Document the addressing scheme. a. Assign the first usable IP addresses to for the two LAN links and the WAN link. b. Assign the first usable IP addresses to address for the WAN link. c. for the two LAN links. Assign the last usable IP Assign the second usable IP addresses to the switches. d. Assign the last usable IP addresses to the hosts. Part 3: Assign IP Addresses to Devices and Verify Connectivity Most of the IP addressing is already configured on this network. Implement the following steps to complete the addressing configuration. Step 1: Configure IP addressing on the router LAN interfaces. Step 2: Configure IP addressing on the , switch including the default gateway. Step 3: Configure IP addressing on , including the default gateway. Step 4: Verify connectivity. , You can only verify connectivity from be able to ping every IP address listed in the Addressing Table. End of document , and . However, you should